Mapei Ultracolor Plus Tile Grout is made up of a blend of special hydraulic binders, graded aggregates, special polymers, water repellent admixtures, organic molecules and pigments. Always carry out preliminary tests before grouting stone or ground porcelain with a porous or rough surface. For flexible expansion joints or joints subject to movement use an elastic sealant from the Mapei line (e.g. Mapesil AC, Mapesil LM, Mapeflex PU45 FT or Mapeflex PU21). Preparing the mix: While stirring, pour the Mapei Ultracolor Plus Grout powder into a clean, rust-free container containing 21-23% by weight of clean water. Mix the grout with a low-speed mixer to avoid air entrainment, until a smooth paste is obtained. Let the mix stand for 2-3 minutes, and stir again briefly before use. Use the mix within 20-25 minutes of its preparation. AB, DD, IV, KW, PH, FK, FY, TR, PA, KA, LL, PO , SA, CA, DG, EH, EX, G, LD, ML, PL, SY, TA, TD AND TQ.

Finishing: When the mix loses its plasticity and becomes opaque, which usually takes place after 15-30 minutes, clean off the excess Ultracolor Plus with a hard, damp sponge (e.g. a MAPEI sponge), working in a diagonal direction to the joints. Rinse the sponge frequently, using two different containers of water: one to remove the excess mix from the sponge, and the other, containing clean water, to rinse the sponge. This operation may also be carried out with a machine with a sponge belt or rotating disc. When the mix is partially set, after 50-60 minutes, a damp Scotch-Brite® sponge or an abrasive felt disc may be passed over the joints to even out the surface. Unglazed klinker tiles should be grouted with the same colour tone Kerapoxy. All other colours should be used only with glazed tiles. Mapei Kerapoxy Epoxy Tile Grout is a two-component acid-resistant epoxy grout for joints of at least 1mm in width. Can also be used as an adhesive. Due to insurance and health and safety regulations we are unable to transport goods into a Customer’s property Mapei Ultracolor Plus does not contain Portland cement and must not be mixed with gypsum or other hydraulic binders; never add water to the mix once it has started to set.Expansion and movement joints on walls and floors must never be filled with Mapei Ultracolor Plus. Use a suitable flexible sealant from the MAPEI range. Mapei Kerapoxy Epoxy Tile Grout is a two-component, epoxy-resin based product with silica sand and special components, with excellent resistance to acids and excellent cleanability. This is a product with very low emission of volatile organic compounds and is classified Emicode EC1 R Plus by GEV when used for grouting. The following features are obtained when used correctly: Grouting floors and walls in the food industry (dairies, abattoirs, breweries, wine-cellars, conserved-food plants, etc.), shops and areas where hygiene is required (ice-cream shops, butchers, fish vendors, etc.). After grouting with Mapei Kerapoxy, floors and walls should be cleaned immediately, before the product dries. Wet the surface thoroughly and emulsify with an abrasive pad for cleaning joints (such as Scotch-Brite or Kerakoll Cleaning Pads), making sure not to wash-out the joints. When cleaning walls, the cleaning pad should be fully soaked with water. The excess liquid can be removed with a hard cellulose sponge (e.g. Kerakoll Cellulose Sponge Float), and should be replaced when too full of resin. Use the same type of sponge for the final tooling of the grout. It is very important that once the finishing process has ended, no traces of Mapei Kerapoxy are left on the tile surface because it will be very difficult to remove. It is therefore necessary to frequently rinse the sponge with clean water during the cleaning process.When finishing large floor surface areas, use a rotary, disc-type power float with Scotch-Brite® abrasive pads, well saturated with water. All excess liquid can be removed with a rubber squeegee. The final cleaning cycle may be carried out using Mapei Ultracare Kerapoxy Cleaner for epoxy grout (special cleaning solution for epoxy grout). Mapei Kerapoxy Cleaner may also be used to remove thin residues of grout several hours after application. In such cases, the product must be left to react for longer (15-20 mins.). The efficiency of Mapei Kerapoxy Cleaner depends on the amount of resin residues and how much time has passed since application. Cleaning must always be carried out while “fresh” as described above.

You must be available to accept delivery on the date you have requested, failure to do so will result in paying for a re delivery charge. Mapei Ultracolor Plus is suitable for grouting walls and floors in areas that are subject to intense traffic, such as shopping centres, airports, restaurants and other public spaces. It is also suitable for residential use in all areas, such as facades, balconies, terraces and swimming pools.Mapei Ultracolor Plus creates water repellent grout joints that have excellent colour uniformity. All colours are resistant to UV rays and atmospheric agents. Spread Mapei Kerapoxy with an appropriate grout float, making sure the joints are completely filled. Use the same float, but on edge, to remove excess grout. Delivery charges vary for the following postcodes and will be delivered between 5-7 working days to the following postcodes: GY, HS, IM, IV41,IV30, IV42, IV44 – 49, IV55, IV56, JE, KA27 – 29, KW1 – 14, KW15 – 17, PA21 – 38, PA20, PA40+, PH9, PH15 – 20, PH32 – 44, PH49, PH50, TR21 – 25, ZE. From our carrier you will receive a text message on the day of the delivery with a 2 hour delivery window. If there any changes or delays you will receive an update via text.